Global site
ACR Machine Tool
Bangladesh HMC400L horizontal machining center
Category:
BangladeshHorizontal machining center
Product Description
one. The main technical parameters
|
Mobile itinerary |
Left and right stroke ( X) mm |
650 |
|
|
Front and rear travel ( Z ) mm |
400 |
||
|
Up and down stroke ( Y ) mm |
500 |
||
|
2. Workbench specifications |
Workbench surface size mm |
315 |
|
|
Workbench load capacity Kg |
350 |
||
|
5. Spindle taper hole ( model / sleeve diameter mm) |
BT 40 /Φ 120 |
Remark: The high-speed synchronous toothed belt driven spindle produced by Taiwan's Danquan has a spindle speed of up to 8,000 rpm and an overall reinforced specially designed bed structure, which is particularly suitable for special processing requirements of high strength, high efficiency, and high-quality surface finish. |
|
|
6. Spindle speed ( RPM revolutions/minute ) |
8 000
|
||
|
7. Recommended motor parameters ( Main motor / Kw , A. X , Y , Z axis /Kw ) |
Spindle 5.5/7.5Kw; X axis 10; Y axis 10 ; Z axis 15 ; A-axis 7.7; |
||
|
8. Ball screw |
X Y Z axis ball screw specifications mm |
3210 |
The three axes use Taiwan's Shangyin C3 high-amplitude and precision pre-tensioned ball screws. |
|
9. Connection (transmission) method |
XYZ .A motor connection method |
Direct connection (transmission) |
|
|
Spindle connection method |
Belt (drive) |
||
|
10. Feed speed G00 , G01 (rate) |
G00 rapid feed mm/min Rapid federate |
X- axis rapid feed mm/min |
20m/min |
|
Y- axis rapid feed mm/min |
15m/min |
||
|
Z- axis rapid feed mm/min |
20m/min |
||
|
Minimum input unit mm |
Pulse equivalentmm |
0.001 |
|||
|
12. Machine tool accuracy mm |
Repeat positioning accuracy mm |
± 0.0085 |
Remarks: Machine tool accuracy testing standards (high standards, high precision) ⑴JB/T 8771.2-1998 "Geometric Accuracy Inspection of Vertical Machining Centers" ⑵JB/T8771.4-1998 "Inspection of Linear Positioning Accuracy and Repeated Positioning Accuracy of Machining Centers" ⑶JB/T8771.7-1998 "Accuracy Inspection of Finished Samples of Machining Centers" ⑷JB/T8801-1998 "Technical Conditions for Machining Centers" |
||
|
Positioning accuracy mm |
± 0.010/300 |
||||
|
13.Pneumatic system Air pressure requirement Kg/cm2 |
≥6 |
Remark: The pneumatic system is equipped with a three-point combination, pressure switch, solenoid valve, etc., to realize pneumatic tool change, spindle air blowing, pressure 6-8kg/cm2, flow rate 220L/min, and an external air gun to clean the working area. |
|||
|
14. Cooling system Cooling system volume L |
300 |
Remark: Sichuan Jianyang cooling pump, motor power 180W, flow rate 40L/min, Cutting cooling uses a universal nozzle to spray coolant. |
|||
|
15. Lubrication system Maximum pressurekg /cm2 |
5 |
Remarks: Japan Valley automatic lubrication device is used to perform forced lubrication on each sliding surface and ball screw; the oil filling time interval and oil filling amount are adjustable; the lubrication tank capacity is 2L. Centralized three-axis bearings and slideways are lubricated. |
|||
|
16. Electric control cabinet cooling system |
|
Machine tool standard configuration |
|
||
|
|
Machine tool options |
||||
|
17. Spindle cooling system |
air cooling |
Machine tool standard configuration |
spindle fan |
||
|
Oil cooler |
Machine tool options |
spindle fan |
|||
|
18. Electrical system |
National standard |
Remarks: It complies with the standard of GB/T5226.1-1996 "Industrial Machinery and Electrical Equipment Part 1: General Technical Conditions"; the system has complete and reliable interlocking, safety protection and fault self-diagnosis and alarm functions; it is equipped with RS232 standard communication interface and can be used with a computer Floppy disks are used to store programs (corresponding software can be provided according to user requirements); other systems can be selected according to user requirements; the electrical cabinet circuit adopts national standards, far exceeding the standards of various manufacturers, and still has its stability under harsh use conditions and durable properties. |
|||
|
19.Machine tool power supply |
Machine tool power supply voltage range V |
AC three-phase 380V ± 10% 50Hz |
|||
|
Total power consumption of machine tools Kva |
≤ 35 |
||||
|
20. Machine tool appearance dimensions (machine tool protection system) mm |
m Standard color of machine tools: upper white and lower gray |
Remark: The machine tool protection device is safe, complete and reliable; it complies with GB15760-1995 "General Technical Spare Parts for Safety Protection of Metal Cutting Machine Tools"; the machine tool noise: complies with the national standard <75db |
|||
|
21. Mechanical weight Kg |
Gross weightKg |
4.5 |
|||
|
22.Normal usage conditions |
Ambient temperature ℃ |
0—40 |
|||
|
humidity % |
≤85 |
||||
2. Main configuration list
|
serial number |
name |
Model or drawing number |
Origin |
quantity |
Remark |
|
1 |
Spindle unit |
BT 40 (sleeve φ1 2 0 ) belt type |
Taiwan Danquan |
1 set |
|
|
2 |
Pressurized cutting cylinder |
40 00 |
Taiwan Danquan |
1 set |
|
|
3 |
X- direction ball screw pair |
3210 |
Jiangsu Qijian |
1 set |
|
|
4 |
Y- direction ball screw pair |
3210 |
Jiangsu Qijian |
1 pair |
|
|
5 |
Z- direction ball screw pair |
3210 |
Jiangsu Qijian |
1 pair |
|
|
6 |
Special bearings for lead screw |
|
Taiwan Bank of China |
6 groups |
|
|
7 |
Screw lock nut |
M24*1.5 |
Taiwan Yingxi |
6 pieces |
|
|
8 |
Spindle bearings |
|
Japan NSK |
4 |
|
|
9 |
Flexible coupling |
|
Jinqiaotong |
3 sets |
|
|
1 0 |
Lubrication system |
Single line positive displacement lubrication oil pump |
river valley |
1 set |
|
|
1 1 |
Pneumatic system |
Triplet 3000 |
Taiwan Zhuoliang |
1 set |
|
|
12 |
balanced system |
Liquid nitrogen balance bar |
Domestic |
1 set |
|
|
13 |
Disc tool magazine |
BT40/20T horizontal |
Taiwan Okada |
1 set |
|
|
14 |
CNC turntable |
TK13315 |
Yantai |
|
|
|
15 |
CNC system |
Beijing KND1000 |
Beijing |
1 set |
|
|
16 |
Internal protection |
Special for sleeping and sleeping |
Six tripod sheet metal |
1 set |
|
|
17 |
External protection |
Special for sleeping and sleeping |
Guanwei sheet metal |
1 set |
|
|
18 |
Ball linear rail |
35 |
Taiwan Bank of China |
6 sets |
|