Global site
ACR Machine Tool
Barbados HMC500 horizontal machining center
Category:
BarbadosHorizontal machining center
Product Description
one. The main technical parameters
|
Mobile itinerary |
Left and right stroke ( X) mm |
8 00 |
|
|
Front and rear travel ( Y) mm |
65 0 |
||
|
Up and down stroke ( Z) mm |
7 00 |
||
|
2. Workbench specifications |
Workbench surface size mm |
500 * 50 0 |
|
|
Workbench load capacity Kg |
5 00 |
||
|
5. Spindle taper hole ( model / sleeve diameter mm) |
BT 4 0/Φ1 5 0 |
Remark:Taiwan-made high-speed synchronous toothed belt drives the spindle, with the spindle speed up to 8,000 rpm and the overall reinforced specially designed bed structure, which is particularly suitable for special processing requirements of high strength, high efficiency, and high-quality surface finish . |
|
|
6. Spindle speed ( RPM revolutions/minute ) |
8 000
|
||
|
7. Recommended motor parameters ( Main motor / Kw , A. X , Y , Z axis /Kw ) |
Spindle 7.5 /1 1 Kw; X axis 2.2 Kw ; Y axis 2.2 Kw ; Z axis 2.2 Kw ; A rotation axis 1.5 Kw; |
||
|
8. Ball screw |
X Y Z axis ball screw specifications mm |
4012 |
The three axes adopt Taiwan's P 3 level high-amplitude and precision pre-tensioned ball screws. |
|
9. Connection (transmission) method |
XYZ motor connection method |
Direct connection (transmission) |
|
|
Spindle connection method |
Belt (drive) |
||
|
10. Feed speed G00 , G01 (rate) |
G00 rapid feed mm/min Rapid federate |
X- axis rapid feed mm/min |
24 m/min |
|
Y- axis rapid feed mm/min |
20 m/min |
||
|
Z- axis rapid feed mm/min |
24 m/min |
||
|
11.Roller wire gauge |
X-direction roller wire gauge specifications |
45 |
The three-axis wire gauge adopts Taiwan's H-grade high-precision roller wire gauge. |
|
Y-direction roller wire gauge specifications |
4 5 |
||
|
Z-direction roller wire gauge specifications |
45 |
||
|
Minimum input unit mm |
Pulse equivalentmm |
0.001 |
|||
|
13. Machine tool accuracy mm |
Repeat positioning accuracy mm |
± 0.0085 |
Remarks: Machine tool accuracy testing standards (high standards, high precision) ⑴JB/T 8771.2-1998 "Geometric Accuracy Inspection of Vertical Machining Centers" ⑵JB/T8771.4-1998 "Inspection of Linear Positioning Accuracy and Repeated Positioning Accuracy of Machining Centers" ⑶JB/T8771.7-1998 "Accuracy Inspection of Finished Samples of Machining Centers" ⑷JB/T8801-1998 "Technical Conditions for Machining Centers" |
||
|
Positioning accuracy mm |
± 0.010/300 |
||||
|
14.Pneumatic system Air pressure requirement Kg/cm2 |
≥6 |
Remark: The pneumatic system is equipped with a three-point combination, pressure switch, solenoid valve, etc., to realize pneumatic tool change, spindle air blowing, pressure 6-8kg/cm2, flow rate 220L/min, and an external air gun to clean the working area. |
|||
|
15. Cooling system Cooling system volume L |
240 |
Remark: Sichuan Jianyang cooling pump, motor power 180W, flow rate 40L/min, Cutting cooling uses a universal nozzle to spray coolant. |
|||
|
16. Lubrication system Maximum pressurekg /cm2 |
6 |
Remarks: The Valley automatic lubrication device is used to perform forced lubrication on each sliding surface and ball screw; the oil filling time interval and oil filling amount are adjustable; the lubrication tank capacity is 2L. Centralized three-axis bearings and slideways are lubricated. |
|||
|
17. Electric control cabinet cooling system |
Hot and cold exchanger |
Machine tool standard configuration |
Remarks: The electric control cabinet is cooled by a heat and cold exchanger, sealed and dust-proof, with a dust-proof grade of IP65 |
||
|
Electric cabinet air conditioner |
Machine tool options |
||||
|
18. Spindle cooling system |
air cooling |
Machine tool standard configuration |
spindle fan |
||
|
Oil cooler |
Machine tool options |
spindle fan |
|||
|
19. Electrical system |
National standard |
Remarks: It complies with the standard of GB/T5226.1-1996 "Industrial Machinery and Electrical Equipment Part 1: General Technical Conditions"; the system has complete and reliable interlocking, safety protection and fault self-diagnosis and alarm functions; it is equipped with RS232 standard communication interface and can be used with a computer Floppy disks are used to store programs (corresponding software can be provided according to user requirements); other systems can be selected according to user requirements; the electrical cabinet circuit adopts national standards, far exceeding the standards of various manufacturers, and still has its stability under harsh use conditions and durable properties. |
|||
|
20.Machine tool power supply |
Machine tool power supply voltage range V |
AC three-phase 380V ± 10% 50Hz |
|||
|
Total power consumption of machine tools Kva |
≤ 20 |
||||
|
21. Machine tool appearance dimensions (machine tool protection system) mm |
255 0mm* 268 0mm*2 5 50mm Standard color of machine tools: upper white and lower gray |
Remark: The machine tool protection device is safe, complete and reliable; it complies with GB15760-1995 "General Technical Spare Parts for Safety Protection of Metal Cutting Machine Tools"; the machine tool noise: complies with the national standard <75db |
|||
|
22. Mechanical weight Kg |
Gross weightKg |
6500 |
|||
|
23.Normal usage conditions |
Ambient temperature ℃ |
0—40 |
|||
|
humidity % |
≤85 |
||||
|
Note: Our company is improving the machine at any time, so we reserve the right to change the technical parameters without prior notice. If a contract is signed, the terms of the contract shall prevail. |
|||||
Main configuration list
|
serial number |
name |
Model or drawing number |
Origin |
quantity |
Remark |
|
1 |
Spindle unit |
BT 4 0 (sleeve φ1 5 0 ) belt type |
Taiwan Danquan |
1 set |
|
|
2 |
Pressurized cutting cylinder |
45 00 |
Taiwan Airtac |
1 set |
|
|
3 |
X- direction ball screw pair |
4012 |
Taiwan Bank of China |
1 set |
|
|
4 |
Y- direction ball screw pair |
4012 |
Taiwan Bank of China |
1 pair |
|
|
5 |
Z- direction ball screw pair |
4012 |
Taiwan Bank of China |
1 pair |
|
|
6 |
X direction ball wire gauge |
|
Taiwan Bank of China |
2 pairs |
|
|
7 |
Y direction ball wire gauge |
|
Taiwan Bank of China |
2 pairs |
|
|
8 |
Z direction ball wire gauge |
|
Taiwan Bank of China |
2 pairs |
|
|
9 |
Special bearings for lead screw |
|
JapanNTN _ |
6 groups |
|
|
10 |
Screw lock nut |
M30*1.5 |
Taiwan Yingxi |
6 pieces |
|
|
1 1 |
Spindle bearings |
|
Japan NSK |
4 |
|
|
12 |
Flexible coupling |
|
Taiwan |
3 sets |
|
|
1 3 |
Lubrication system |
Single line positive displacement lubrication oil pump |
japan river valley |
1 set |
|
|
1 4 |
Pneumatic system |
Triplet 3000 |
Taiwan Airtac |
1 set |
|
|
15 |
balanced system |
Liquid nitrogen balance bar |
Taiwan |
1 set |
|
|
16 |
Disc tool magazine |
BT 4 0/24T horizontal |
Taiwan Okada |
1 set |
|
|
17 |
CNC turntable |
TK56 50 0* 50 0 rotary table |
Yantai Global |
1 set |
|
|
18 |
CNC system |
KND2000MC1I |
Beijing Kaindi |
1 set |
|
|
19 |
Internal protection |
50 0 sleeping plus special |
Haidong sheet metal |
1 set |
|
|
20 |
External protection |
50 0 sleeping plus special |
Meg Sheet Metal |
1 set |
|